everlight electronics co., ltd. http:\\www.ev erlight.com rev 2 page: 1 of 10 device no dth-067-169 prepared date 04-12-2006 prepared by jaine tsai technical data sheet top infrared led hir67-21c/l11/tr8 features ? peak wavelength p=850nm. ? low forward voltage. ? compatible with infrared and vapor phase reflow solder process. ? package in 8mm tape on 7? diameter reels. ? pb free ? the product itself will remain within rohs compliant version. descriptions ? hir67-21c/l11/tr8 is an infrared emitting diode in miniature smd package which is molded in a water clear plastic with flat top view lens. the device is spectrally matched with silicon photodiode and phototransistor. applications ? floppy disk drive ? optoelectronic switch ? camera ? vcr ? video ? smoke detector device selection guide chip led part no. material lens color hir gaalas water clear
everlight electronics co., ltd. http:\\www.ev erlight.com rev 2 page: 2 of 10 device no dth-067-169 prepared date 04-12-2006 prepared by jaine tsai hir67-21c/l11/tr8 package dimensions notes: 1.all dimensions are in millimeters 2.tolerances unless dimensions 0.1mm absolute maximum ratings (ta=25 ) parameter symbol rating units continuous forward current i f 65 ma reverse voltage v r 5 v operating temperature t opr -25 ~ +85 storage temperature t stg -40 ~ +85 soldering temperature t sol 260 power dissipation at(or below) 25 free air temperature p d 130 mw notes: *1:soldering time Q 5 seconds.
everlight electronics co., ltd. http:\\www.ev erlight.com rev 2 page: 3 of 10 device no dth-067-169 prepared date 04-12-2006 prepared by jaine tsai hir67-21c/l11/tr8 electro-optical characteristics (ta=25 ) parameter symbol condition min. typ. max. units i f =20ma 1.0 2.0 -- radiant intensity ee . i f =100ma pulse width Q 100 s ,duty Q 1% -- 10 -- mw /sr peak wavelength p i f =20ma -- 850 -- nm spectral bandwidth ? i f =20ma -- 45 -- nm i f =20ma -- 1.45 1.65 forward voltage v f . i f =100ma pulse width Q 100 s ,duty Q 1% -- 1.80 2.40 v reverse current i r v r =5v -- -- 10 a view angle 2 1/2 i f =20ma -- 120 -- deg
everlight electronics co., ltd. http:\\www.ev erlight.com rev 2 page: 4 of 10 device no dth-067-169 prepared date 04-12-2006 prepared by jaine tsai 790 0 20 40 60 80 100 890 850 810 830 870 930 910 950 i f =20ma ta=25 c 75 -25 800 0 825 850 25 50 875 900 100 0 -25 0 40 20 60 100 80 20 40 60 100 80 120 140 0 10 1 10 10 2 3 10 4 2 1345678 hir67-21c/l11/tr8 typical electro-optical characteristics curves fig.1 forward current vs. fig.2 spectral distributio n ambient temperature fig.3 peak emission wavelength fig.4 forward current ambient temperature vs. forward voltage
everlight electronics co., ltd. http:\\www.ev erlight.com rev 2 page: 5 of 10 device no dth-067-169 prepared date 04-12-2006 prepared by jaine tsai 25 1 1.2 1.4 1.6 50 75 100 120 i f =20ma -20 0.6 0.9 0.7 0.8 1.0 0.2 0.4 0 0.2 0.4 0.6 50 70 80 60 40 30 -10 020 10 25 1.0 1.5 50 75 100 120 i f =20ma 2.0 2.5 0 i f -forward current (ma ) 10 10 0 10 1 10 23 10 4 ie-radiant intensity(mw/sr) 1 10 100 hir67-21c/l11/tr8 typical electro-optical characteristics curves fig.5 relative intensity vs. fig.6 relative radiant intensity vs. forward current angular displacement fig.7 relative intensity vs. fig.8 forward voltage vs. ambient temperature( c) ambient temperature( c)
everlight electronics co., ltd. http:\\www.ev erlight.com rev 2 page: 6 of 10 device no dth-067-169 prepared date 04-12-2006 prepared by jaine tsai hir67-21c/l11/tr8 precautions for use 1. over-current-proof customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( burn out will happen ). 2. storage 2.1 do not open moisture proof bag before the products are ready to use. 2.2 before opening the package, the leds should be kept at 30 or less and 90%rh or less. 2.3 the leds should be used within a year. 2.4 after opening the package, the leds should be kept at 30 or less and 70%rh or less. 2.5 the leds should be used within 168 hours (7 days) after opening the package. 2.6 if the moisture absorbent material (silica gel) has faded away or the leds have exceeded the storage time, baking treatment should be performed using the following conditions. baking treatment : 60 5 for 24 hours. 3. soldering condition 3.1 pb-free solder temperature profile 3.2 reflow soldering should not be done more than two times. 3.3 when soldering, do not put stress on the leds during heating. 3.4 after soldering, do not warp the circuit board.
everlight electronics co., ltd. http:\\www.ev erlight.com rev 2 page: 7 of 10 device no dth-067-169 prepared date 04-12-2006 prepared by jaine tsai hir67-21c/l11/tr8 4.soldering iron each terminal is to go to the tip of soldering iron temperature less than 280 for 3 seconds within once in less than the solderi ng iron capacity 25w. leave two seconds and more intervals, and do soldering of each terminal. be car eful because the damage of the product is often started at the time of the hand solder. 5.repairing repair should not be done after the leds have been soldered. when repairing is unavoidable, a double-head soldering iron should be used (as below figure). it should be confirmed beforehand whether the characteristics of the leds will or will not be damaged by repairing.
everlight electronics co., ltd. http:\\www.ev erlight.com rev 2 page: 8 of 10 device no dth-067-169 prepared date 04-12-2006 prepared by jaine tsai hir67-21c/l11/tr8 reliability test item and condition the reliability of products shall be satisfied with items listed below. confidence level 90% ltpd 10% no. item test conditions test hours/ cycles sample sizes failure judgement criteria ac/re 1 reflow temp. 260 5 5secs 6mins 22pcs 0/1 2 temperature cycle h : 100 15mins 5mins l : -40 15mins 50cycles 22pcs 0/1 3 thermal shock h :+100 5mins 10secs l :-10 5mins 50cycles 22pcs 0/1 4 high temperature storage temp. +100 1000hrs 22pcs 0/1 5 low temperature storage temp. -40 1000hrs 22pcs 0/1 6 dc operating life i f =20ma 1000hrs 22pcs 0/1 7 high temperature/ high humidity 85 / 85% r.h 1000hrs 22pcs i r R u 2 ee Q l 0.8 v f R u 1. 2 u upper specification limit l lower specification limit 0/1
everlight electronics co., ltd. http:\\www.ev erlight.com rev 2 page: 9 of 10 device no dth-067-169 prepared date 04-12-2006 prepared by jaine tsai hir67-21c/l11/tr8 package dimensions taping dimensions
everlight electronics co., ltd. http:\\www.ev erlight.com rev 2 page: 10 of 10 device no dth-067-169 prepared date 04-12-2006 prepared by jaine tsai rohs hir67-21c/l11/tr8 packing quantity specification 1.2000pcs/1volume 1volume/1bag 2.10boxes/1carton label form specification cpn: customer?s production number p/n : production number qty: packing quantity cat: ranks hue: peak wavelength ref: reference lot no: lot number made in taiwan: production place notes 1. above specification may be changed without notice. everlight will reserve authority on material change for above specification. 2. when using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sh eets. everlight assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 3. these specification sheets include material s protected under copyright of everlight corporation. please don?t reproduce or cause a nyone to reproduce them without everlight?s consent. everlight electronics co., ltd. tel: 886-2-2267-2000, 2267-9936 office: no 25, lane 76, sec 3, chung yang rd, fax: 886-2267-6244, 2267-6189, 2267-6306 tucheng, taipei 236, taiw an, r.o.c http:\\www.everlight.com hir67-21c/l11/tr8
|
